GOTEK FLOPPY DISK EMULATOR SERIAL
So many products come with USB cables as they’re so cheap.” However, I plumbed for the second option since I had a few Serial to USB adaptors from programming Arduinos etc. Zeb Elwood on Facebook said “(it is easy) to make one by cutting up two USB cables and joining the color-coded wires together, simple as there’s only four. You can either use a non-standard USB ‘A’ to USB ‘A’ cable, which I didn’t have, or use a Serial to USB adaptor. Programming the Gotek drive can be done in two ways. I also knew that Kier’s firmware supported the OLED display modification which was a feature I particularly wanted. I understood that the Cortex firmware was no longer supported and HxC had a charge associated with it. Kier Fraser has written some really nice firmware for the Gotek drives. I ordered one, again from eBay (Search for KY-040 Module), and got on with other research. This seemed pretty easy and uses an easy to obtain module. Rene kindly gave me permission to repost it here. I found a post on an Amiga Forum page by Fook42 (Rene) that had details of the Rotary Encoder wiring.
GOTEK FLOPPY DISK EMULATOR MOD
I already knew you could add a nice OLED Display, a Rotary Encoder and even a speaker if you wanted authentic disk drive sounds! Another mod was to make a hole for the unused power LED concealed in the case.
GOTEK FLOPPY DISK EMULATOR HOW TO
Whilst I waited for the Gotek, I did some research on how to enhance it. I did a bit of research and, guided by Keir Fraser, I bought the cheapest Gotek drive I could on my favorite online auction site ( eBay). Instead of floppy disks, you use a USB memory Stick that can hold up to 1000 (000-999) virtual disk images. Until I was given a box of new-old stock DS/DD disks by my good friend Russell, I wouldn’t have relied on any of them.Įnter the Gotek, the ideal solution. I bought a batch from eBay and they range from usable to completely useless. I’ve been using a 3.5in floppy drive with my Datel +D Interface for a while but I have found that floppy disks can be a little tempremental due to their age, and I’m not surprised. This device, very cleverly, stands in as a real hardware floppy drive. You can launch it from Workbench and return to workbench without the need to reboot the machine.Īnd of course HxC firmware for Gotek support OLED screens, rotary, extra buttons too.In the not too distant past, I was made aware of the Gotek Floppy Drive Emulator. The latest file selector for HxC Floppy Emulators and HxC Firmware for Gotek is compatible with Workbench : So I think the description is complete I probably missed a detail somewhere so please fill in. Stick it in an external drive case and solder a DF0/DF1 switch on the motherboard. If this is not OK, there's another solution. So the long and short of it is that Gotek is not made for Amiga, and at some point you will probably have to carve the case somewhat to get it usable. (USB sticks are cheap, just get one that allows you to do this and you can use it for all your Goteks, I have 3.) I removed the plastic shell around mine and wrapped some electrical tape.
![gotek floppy disk emulator gotek floppy disk emulator](https://i.ebayimg.com/images/g/4qIAAOSwOIxck2UF/s-l500.jpg)
Most USB sticks will not be insertable through the floppy slit. Only the OLED display can be viewed through the floppy slit (and barely).
![gotek floppy disk emulator gotek floppy disk emulator](https://www.nightfallcrew.com/gallery/gotek-cortex-usb-floppy-disk-drive-emulator/IMG_1286.jpg)
Maybe 1 and 2 do too though.īuttons can be reached through the floppy slit with a so-called utensil. Image is selected by buttons (built in) or rotary. So 3 methods of image selection in all, of which one is similar to "boot 000 selector image to assign images to slots" of Cortex. It can also work in HxC mode and Native mode (which makes you rename 10 images as 10 disks and these are the slots you flip through). FlashFloppy (and probably HxC as well, not tested by me) supports a small OLED display that looks extremely sharp and is easier to fit. It's big and backlit and looks pretty smart.ģ. HxC supports a large LCD display ("make a hole in your case") that shows the name.
![gotek floppy disk emulator gotek floppy disk emulator](https://amsynths.co.uk/wp-content/uploads/2019/08/Gotek-Drive-in-S-220-Outside-scaled.jpg)
adf files to number 001-999 selected with buttons.Ģ. Cortex=hex display where image 000 is a disk image with a selector that lets you assign.
![gotek floppy disk emulator gotek floppy disk emulator](https://www.u-buy.com.tw/productimg/?image=aHR0cHM6Ly9pLmViYXlpbWcuY29tL2ltYWdlcy9nL01nUUFBT1N3TGNOY2xqU3Mvcy1sNTAwLmpwZw.jpg)
There are several solutions for disk selection: Cortex, HxC, and FlashFloppy firmware.Īll the solutions have displays for selecting the image to boot.ġ. The videos I have seen show booting from adf image disk 0 to bring up a selector to then allocate whichever disks you want to positions in a list but how can you access that from Workbench? The reason I am asking is that I thought it might be a good option to be able to just get adf versions of disks that I might want to use/work with in Workbench booted from my CF card hard drive. If I was to get a Gotek floppy emulator to replace my internal disk drive on my A1200 can you/how do you select any disk currently on the inserted USB stick whilst in Workbench? I've looked at some YouTube videos and searched the posts one here to see if I could find the answer myself but no joy so far.